Develop a sharp edge even drill bits get dull after a lot of use. When it happens your work slows down and becomes harder to do. There is a way to avoid this situation. All you need is one of the top 10 best drill bit sharpeners.
These top sharpeners make sure you always have an edge and can get your work done correctly. Plus, they are easy to use so you can get back to work without too much delay.
Keeping your tools at a fine edge makes sure your work looks its best as well. That is important when looks count. Go with the best sharpeners so your work is always professional and top-notch
List of Best Drill Bit Sharpeners Reviews
TBZZXC Portable Diamond Drill Bit Sharpening Tool
- Drill Bit Sharpening Tool, easy and convenient to use.
- High quality ABS plastic and brown corundum grinding wheel, wear-resistant, rustproof, waterproof and dustproof.
- Mainly used for the iron type bit, other high hardness drills may be not suitable, please note before purchasing.
- Use this drill bit sharpener with your power drill to keep bits sharp and ready for use, save and practical.
- Lightweight and portable, 3 sizes, available for 2mm to 12.5mm bit.
Get a razor edge on your drill bits when you employ this top drill bit sharpener. It is easy to use and attaches to your drill to get the sharpening bit up to speed. Once you have attached the sharpener you have a tough sharpening head that handles lots of drill bits.
Made from tough yet lightweight ABS plastic, your hands should not tire out as you sharpen drill bit after drill bit. On top of that, you have 3 specially marked slots to put the right drill bits inside to sharpen them properly. Those markings are found on the handle with an arrow pointing to the corresponding slot.
A wrench is included to make sure any adjustments you need to make are done correctly and quickly. This sharpener is made for those iron drill bits you have lying around. Plus, this sharpener is very portable and it’s approx. 7 by 3-inch size should fit in your toolbox with ease.
The sharpening wheel is wear-resistant, rust, water, and dustproof. It holds up so you can save a lot of money not buying replacement drill bits.
Central Purchasing, LLC Multipurpose Sharpener for Drill Bits
No products found.
This easy-to-use drill bit sharpener has a powerful motor that runs at about 4,800 rpm. That is more than enough power to sharpen your drill bits. Plus, it comes with rubber feet to make sure you do not feel a lot of vibration as you work.
On to[p of that, you have pre-drilled holes that allow you to bolt this sharpener to your workbench for easier and more stable use. Once you have it in place you have a powerful sharpening tool helping you out.
In addition, this drill bit sharpener can handle scissors, knives, chisels, and just about any small-sized implement that needs a sharp edge. Also, the 70-watt motor does not produce a lot of sounds but it provides you with very efficient work.
If that is not enough, this sharpener helps you locate those drill bit angles accurately. You should not have trouble getting sharp bits once you are finished. This is a workplace essential that makes your work life easier to do.
GOODSMANN Electric Drill Bit Sharpener
No products found.
The top-quality plastic body is very durable. It should stand up to normal wear and tear without breaking into a sweat. Plus, its bright color reminds you of where it is sitting. There is no lost time spent looking for this top sharpening tool.
Getting the right edge on your drill bits will not be hard at all. The top of this device comes with a spin dial. On that dial are reference measurements and appropriately sized holes. Just slip the drill bit into the correct hole and you should have a sharp bit when you pull it back out again.
As long as your drill bits measure between 1/8″ to 25/64″ in size, you should not have trouble sharpening up old and dull drill bits. Simple to use rocker switch is all the buttons you need to push. Getting power to this device is easier than ever.
Its compact size makes it hard to move when you are working. Then when you run out of drill bits, you can always sharpen knives and scissors on this unit.
Multi-Sharp Dual Purpose Drill and Tool Sharpener
No products found.
This is a stationary drill bit sharpener that can attach to your drill in no time at all. Once you have it in place, the sharpener has a stabilizing foot to make sure the wheels do not alter their position on you at the wrong time.
Plus, you have lots of accessories to help you sharpen your drill bits. Each piece makes sure you come away with a fine sharp edge that cuts through those tough metals with ease.
One of those accessories helps you get the right angle you need each and every time. That makes your sharpening chore go faster and a lot smoother. This device should fit just about any drill you have in your home or job site.
Also, drill bits are not the only small tool you can get a sharp edge. This device should handle chisels, punches, awls, and other fine tools that can be sharpened by this drill bit sharpener. With replaceable grinding wheels, you should have this drill bit sharpener around for a long time to come.
CZS Drill Bit Sharpener
Be like the Boy scouts and always be prepared for when bad things happen. Once your drill bit starts to go dull that is not a problem anymore. You can have this portable drill bit sharpener in your toolbox ready to go.
After you get it attached to your drill, you have several slots in which to slide your drill bits. The grinding wheel and drill do all the hard work, you just supply the guiding touch to get those drill bits back into shape.
It’s an easy-to-use tool that comes with its own wrench so you can make the appropriate adjustments when those situations arise. Then with the extra grinding wheel, you can keep on sharpening when the other wheel wears out.
As long as you have iron-based bits and they fit the 5/64”-1/2” boundaries, you can use this portable drill bit sharpener. Made from lightweight ABS plastic for easier handling. A plastic cover protects the wheel from harm.
Grizzly Industrial G1081 – Drill Bit Sharpener
- Grinds and sharpens 1/8" - 3/4" bits
- Package dimensions: 8" x 5" x 1.34"
- Approximate weight: 1.34 lbs
When you have a lot of drill bits to sharpen this may be the tool for you to use. It handles drill bits measuring between 1/8″ – 3/4″. The easy-to-use drill bit sharpener provides you with a scale to make sure you have the right angle and get the right edge sharpened the way you like it.
Once you have the drill bit locked into place, and the bit at the right angle, per the gauge, you are almost done. The next thing you have to do is move the drill bit sharpener next to your bench grinder and start sharpening. That is all there is to sharpen your drill bits with this device.
It is easy to use and manipulate into position. Made from light metals, this device only weighs a little under 1 1/2 pounds. Your hands should not get sore or tired when using this drill bit sharpener. Its 8 by 5-inch size shouldn’t take up a lot of space n your workbench either.
Woodstock D4144 Drill Sharpener
- Sharpen drill bits from 1/8-Inch to 3/4-Inch with speed and accuracy
- Adjustable for various drill-point angles
This top drill bit sharpener also uses your stationary bench grinder to get your bits nice and sharp. All you supply is the guiding touch to make sure you do not over-sharpen your bits and ruin them.
There is a slot on the base where you can bolt the device down so that it will not move till you loosen the bolt. You should be able to get all your bits sharpened at one time. The lightweight drill bit sharpener is easy to maneuver into place and then all you do is tighten the holding bolt down.
After that, you just use the gauges and tightening holders to make sure your drill bits meet the grinder at the right angle. With the ability to help you sharpen 1/8 to 3/4 inch drill bits your work time is greatly helped by this sharpener.
Then this approx. 7 by 5-inch drill bit sharpener just needs to find a small corner till you need to use it again.
Drill Doctor DD500X 500x Drill Bit Sharpener
- SHARPENS STANDARD DRILL/TWIST BITS: The DD500X drill bit sharpener sharpens twist bits from 3/32" to 1/2". Optional 3/4 inch chuck available as an upgrade.
- SHARPEN & SPLIT: Sharpen all common twist-style drill bits and split the cutting tip to reduce wear and increase the cutting performance of your bits.
- SHARPENS TO 118 OR 135 DEGREES: Accommodates all common bit angles to tailor to whatever you need to ensure your bit is in top shape for your work or project.
- 3-YEAR WARRANTY: Protects every Drill Doctor bit sharpener against defects due to workmanship or design.
- DESIGNED, ENGINEERED, & CALIBRATED IN OREGON: We design, engineer, and calibrate our sharpening machines all under one roof in Ashland, Oregon & ensure our products are sourced from the highest caliber manufacturers, both in the USA and globally.
Make your drill bit sharpening chore a lot easier to do. This little drill bit sharpener cuts the work out and makes sure you get top-quality sharp edges every time you use it. It is not hard to learn how to use it.
On top of that, this drill bit sharpener works with most standard twist drill bits measuring between 3/32″ to 1/2″. Plus, you can get a 118 and a 135-degree angle on those drill bits. Just dial the angle in and you are set to go.
The holder makes sure your drill bits do not move during the sharpening process. One part of this device helps you align the drill bit before you put it in the sharpening spot.
If you have the mind to do it and the need, you can create split points out of standard points with a little extra time and a very small amount of effort. This drill bit sharpener gives you lots of options and helps you with accuracy as well.
Drill Doctor DD350X Drill Bit Sharpener
- SHARPENS STANDARD DRILL BITS: The DD350X sharpens drill bits from 3/32" to 1/2". It is ideal for shops that use the most common bit styles and is compatible with wood and light metals.
- PROFESSIONAL DESIGN & CONSTRUCTED FOR DURABILITY: This industrial-strength diamond sharpening wheel won't change shape over time. It also has a cool design, so bits don't heat up & lose their temper as you sharpen them. Contains a 6-foot power cord.
- TWO EASY STEPS: The DD350X eliminates the need for an alignment port & simplifies sharpening. Secure the bit & turn the chuck to achieve a perfect 118° angle. The V-block jaws hold the bit in place so you don't have to worry about jaw twisting.
- 3-YEAR WARRANTY: Protects every Drill Doctor bit sharpener against defects due to workmanship or design.
- DESIGNED, ENGINEERED, & CALIBRATED IN OREGON: We design, engineer, and calibrate our sharpening machines all under one roof in Ashland, Oregon & ensure our products are sourced from the highest caliber manufacturers, both in the USA and globally.
This is a scaled-down version of the previous drill bit sharpener on this list. But even though it doesn’t have all the frills it still sharpens your drill bits to the edge and angle you need.
Once in your home or workshop, this drill bit sharpener works on standard bits measuring between 3/32″ to 1/2″ in size. That means you do not have to throw out old dull bits. You save money by resharpening them to a fine point.
All you have to do is secure the bit in the holder and then tighten it an even amount of times to get the correct 118-degree angle you need. The V-styled jaws make sure the bit does not move on you throughout the whole time you are sharpening it.
It is a very simple drill bit sharpener that removes a couple of steps in the sharpening process. When you are in a hurry those fewer steps may help you finish your work on time.
Drill Doctor 750X Drill Bit Sharpener
- SHARPENS STANDARD DRILL BITS: The DD750X drill bit sharpener sharpens twist bits from 3/32" to 3/4". This professional system can even be used to put an edge back onto broken bits.
- SHARPEN & SPLIT: Sharpen all common twist-style drill bits and split the cutting tip to reduce wear and increase the cutting performance of your bits.
- SHARPENS TO 115-140 DEGREES: Accommodates all common bit angles to tailor to whatever you need to ensure your bit is in top shape for your work or project.
- 3-YEAR WARRANTY: Protects every Drill Doctor bit sharpener against defects due to workmanship or design.
- DESIGNED, ENGINEERED, & CALIBRATED IN OREGON: We design, engineer, and calibrate our sharpening machines all under one roof in Ashland, Oregon & ensure our products are sourced from the highest caliber manufacturers, both in the USA and globally.
This top model handles a variety of drill bit styles. From high speed to masonry to cobalt and more. You can have your whole collection of drill bits sharpened in no time by using this drill bit sharpener.
In addition to that feature, you can sharpen your drill bits at any point between 115 to 140 degrees. That gives you the drill bit sharpening flexibility you need. On top of that, this sharpener works with 3/32-inch to ¾-inch without batting an eye.
Then its 6-foot power cord allows you to position this drill bit sharpener where it is the most convenient for you. Having a comfortable workspace is important when sharpening drill bits.
Then the magnetic motor works efficiently and consistently to make sure all your bits are sharpened just right. You can also do a split point if you want to. There is little that this drill bit sharpener cannot do for you. It should serve you well and for a long time.
Some final words
Getting a professional job done depends a lot on how sharp your tools are. One of the top 10 best drill bit sharpeners in 2019 makes sure your drill bits are sharp enough to produce those professional results.
Plus, they are all easy to use and do not take up a lot of precious workbench space. The top drill bit sharpeners are at your disposal.